Martin Guitars, Blueridge Guitars, Guitar Parts, Guitar Pickups
Martin Guitars
Blueridge
Reverend
Acoustic Guitar Case,Guitar Case - MaurysMusic.com
Mesa/Boogie
D-Tar Pickups, K&K Pickups, Martin Pickups, Fire-Eye Preamps, Radial Preamps, Orchid Preamps, Ultrasound Amps, Fishman Amps, Guitar Pickups, Guitar Amps, Guitar Preamps
Acoustic Guitar Parts, Martin Guitar Parts, Blueridge Guitar Parts, Bridge Pins, Guitar Saddles
Acoustic Guitar Strings, D'Addario Strings, DR Strings, Elixir Strings, John Pearse Strings, Martin Strings
Guitar Cable, Guitar Capo, Guitar Humidifier, Guitar Pick, Guitar Strap, Guitar Stand, Guitar Polish, Guitar Tuner, Guitar Accessories
 Guitar Bridge Pin Sizing Guide 
Please use the sizing chart below for our Fossilized Walrus Ivory, Fossilized Walrus Jawbone, Mammoth Ivory, Buffalo Horn & Bone bridge pins.  All of our bridge pins are slotted.  Inlays are 3mm.
Guitar Manufacturer size
 Alverez Yari 1.3
 Blanchard  1
 Blueridge  1.3
 Collings (prior to 2002)  1
 Fender 4.3
 Garrison 1
 Gibson (prior to 1995) 2A
 Gibson (1995 to Oct 31, 2009) 1.3
 Gibson (Nov 2009 to present) 1
 Goodall 1
 Guild  4.2D
 Huss & Dalton 1.3
 Ibanez 4.3
 Martin (prior to 1994, except HD-28) 1
 Martin (1994 to present) 2A - sits high like original pins
(about 1/4" above the bridge)
or
1.3 - sits lower than 2A
(preferred fit by most people)
 Martin HD-28 (prior to 1994) 2B
 Martin HD-28 (1994 to present) 1.3
 Maton 4.3
 McPherson 1.3
 Olson 4.3
 Ryan 1
 Santa Cruz 1
 Seagull 4.3
 Simon & Patrick 4.3
 Tacoma 4.3
 Takamine (Pro Series only... does NOT fit G Series) 1.3
 Taylor 1

**If your guitar isn't listed, we don't carry bridge pins that will fit and we recommend you contact the guitar manufacturer for bridge pin advice and availability.  We cannot guarantee a fit as pin holes can wear over time with string changes & some manufacturers "adjust" pin holes to fit the bridge pins they have on hand.

 Technical information on bridge pin sizes... see below. 
 Size 1 
* 3º tapered shaft
* 0.210" diameter at the top of the shaft (just below the skirt)
* string slot running the full length of the shaft, stopping below the skirt.
 Size 1.3 
*3 degree tapered shaft with the diameter at the top of the shaft (just below the skirt) of .205 and a string slot running the full length of the shaft,stopping below the ball.
 Size 2A 
* 5º tapered shaft
* 0.220" diameter at the top of the shaft (just below the skirt)
* string slot running the full length of the shaft and cutting through the skirt
 Size 2B 
* The same as Size 2A except the string slot actually stops 1/16" below the bottom of the skirt.
 Size 4.2D 
* 5º tapered shaft
* shaft diameter at the top of the shaft is 0.207" and tapers down to 0.144" with a long (0.945") shaft
* the slot runs the full length of the shaft, stopping below the ball
* these pins do not have a skirt - just a slight ridge beneath the ball
* the slot does penetrate this ridge.
 Size 4.3 
* 3º tapered shaft
* diameter at the top of the shaft is 0.203"
* string slot runs the full length of the shaft
 
 
    Social Media



     

    *Prices are subject to change without notice.